Cart

- Wooden handle for building spades - Ash T-handle - DIN 20152

- Aspen, tropical wood-free - finely sanded

- Aggressive drill bit with 4 cutting edges: robust solid carbide S-cutting edge and angled secondary cutting edges - 2-and-2-helix design, vibration-optimized, for optimum power transmission and speed - Active centring tip for active cutting in ...

Hacksaw no. 10-30-23 - Lightweight high-performance saw with very sturdy frame - Powder-coated frame, protected against rust and corrosion - Easy-to-operate clamping mechanism - Ergonomic handle - With knuckle guard for safe working Delivery: ...

Airboy 186 OF E compressor - Electric motor equipped with motor protection switch - One pressure gauge each for displaying the tank and working pressure - Fully automatic on/off operation - Powder-coated compressed air tank - Oil-free - Pressure ...

Compressed air hose reel SAR 8/10 E - With swivel bracket - For wall or ceiling mounting - Polyurethane compressed air hose with fabric insert - The hose can be locked in place by simply pulling it or rolled up automatically as required Delivery: ...

ProfCut fine saw no. PC-10-DTL - With lightweight steel back for high stability - Fine universal toothing - Hardened tooth tips for long-lasting sharpness - Cranked handle for flush cutting - For wood and plastic

Synthetic drill bit set HW - TC-tipped cutting edges - Center point - 2 spurs - Stepped shank, cylindrical - For drilling holes in hardwood, glued wood, pressed board, chipboard and plastic-coated board materials Delivery: In wooden box.

Synthetic drill bit set HW - TC-tipped cutting edges - Center point - 2 spurs - Stepped shank, cylindrical - For drilling holes in hardwood, glued wood and plastic-coated chipboard Delivery: In Systainer® T-Loc MINI I.

HW slotting cutter - HW-tipped - replaceable teeth with chip thickness limiter - 4 secondary holes with 90° countersink and 36 mm pitch circle - MAN/manual feed

HW end mill set - HW-tipped cutting edges - Shank Ø 8 mm - For softwood, hardwood and coated panel materials Delivery: In Systainer® T-Loc MINI I. Contents: 6 grooving cutters Ø 6; 8; 10; 16; 18; 20 mm 1 flush milling cutter Ø 12.7 mm 1 ...

Carpenter's mallet - Beechwood mallet head - Ash handle - Mallet head and handle glued together - DIN 7461

TCT circular saw blade with alternate teeth - For high demands on cutting quality for single-sided coated and veneered panels, hard fiberboard, chipboard, blockboard, plywood, natural wood, hard paper, hard fabric, hard foam, hard rubber, ...

HW hand-held circular saw blade, alternate tooth, negative - For chop saws - For high demands on cutting quality for single-sided coated and veneered boards, hard fiberboard, chipboard, blockboard, plywood, natural wood, hard paper, hard fabric, hard ...

TCT circular saw blade for rip and cross cuts - For rip and cross cuts in all natural woods, wood panel materials, also veneered on one side or covered with plastic on one side

TCT circular saw blade with universal alternating teeth - For simple, fast cuts in panel materials, veneered or covered with plastic on one side - For veneer in packs lengthwise, hard paper and hard fabric

- Slide rail made of special steel - Housing and bracket made of glass fiber reinforced polyamide - Multi-component plastic handle - Handle with pump lever and integrated release lever - Can be reversed for spreading - Spreading and clamping possible ...

- Precise assembly at a 90° angle - For cleanly fixed and stabilized chuck corners

Mitre box set, with fine saw - 2 mitre cuts 45° - 1 angle cut 90° - Multiplex - Glued Contents: Cutting box and fine saw.

Tool bag for carpentry trainees - Ideally equipped for trainees and woodworkers - Nylon, 1680 denier - Lid with Velcro fastener, detachable - 2 clips for tape measures - 6 outer compartments - 1 additional outer compartment for large tools, e.g. pipe ...

Mitre gauge - Legs and tongue made of beech wood - Accurate angles and firmly glued - Ground surfaces - For marking out and measuring angles at 45° and 135°

Joiner's square - Tongue made of stainless steel - Leg made of beech wood - Handle with groove on both sides - With brass fittings - With mitre and imprinted dimensions

Square - Handle and tongue made of beech wood - Handle with groove on both sides - Angle accurate and firmly glued - Ground surfaces - For marking and measuring rigid angles at 90°

PrizeCut handsaw - Universal toothing - Hardened tooth tips - Long-lasting sharpness - Sturdy, screw-fastened plastic handle - For all types of wood

S-shaped bit no. 1051, with wooden handle - S-shaped blade - White beech handle, flattened - For working in hard-to-reach places

Chisel set no. 1118 SB, with plastic handle - Special tool steel - Forged and polished - Side bevel - DIN 5139 B - 2-component plastic handle Delivery: In box.

Carpenter's chisel no. 1205 - Special tool steel - Forged and polished - Side bevel - White beech handle with leather washer

Snap-off blade RAZAR BLACK BLADE™, 18 mm - Straight cutting edge - Particularly sharp blade for high cutting quality in thin materials - Dispenser with snap-off device - For cutter DC560 Delivery: In dispenser.

Cutter knife LC501, plastic housing - Plastic handle - Metal blade guide - Blade secured by threaded screw Supplied with 2 ENDURA-BLADE™ snap-off blades. Note: The article is subject to § 42a WaffG. It may only be used for professional purposes ...

Hand countersink 90° - 5 cutting edges - Plastic handle - For deburring and countersinking holes in wood and plastic

Double cornice plane - Suitable for double cornice plane no. 10 S

#VALUE!

Joint gluing paper, unperforated - Cellulose paper, 30 g/m², with grease, alkali and acid-free rubber coating - Wet gluing technique - Particularly suitable for light and thin veneers, for hand and machine processing

Mitre box no. 225 - 2 mitre cuts 45° - 1 angle cut 90° - Beech wood - Glued

Woodturning chisel set no. 1635 - Short shape - hornbeam handle Delivery: In plastic bag. Contents: Flat chisel no. 1630 angled, two-ball, 12 mm Gouge no. 1631, 12 mm Chisel no. 1632, 4 mm

Woodturning chisel set no. 1694 - Long shape - hornbeam handle Delivery: In box. Contents: Flat chisel no. 1609, angled, two-ball, 16 mm gouge no. 1619, 20 mm parting chisel no. 1629, 6 mm boring tool no. 1649, round cutting edge, 20 mm

Notched carving knife no. 3351 - Short, slanted cutting edge - hornbeam handle

Notched carving knife no. 3352 - Long, angled cutting edge - hornbeam handle

Notched carving knife no. 3358 - Straight edge - Round back - Hornbeam handle

Carving tool set no. 3424 - special tool steel - hornbeam handle Delivery: In self-service packaging. Contents: Notched carving chisel no. 3201, straight, with straight cutting edge 8 mm Notched carving chisel no. 3208, straight, with medium hollow 8 ...

Carving tool set no. 3441 - special tool steel - hornbeam handle Delivery: In wooden box. Contents: Carving chisel no. 3201, straight, with straight cutting edge 8 mm Carving chisel no. 3202, straight, with angled cutting edge 10 mm Carving chisel ...

Pull saw no. JPR-265R/Y1 - Cross-ground teeth - Induction-hardened teeth - Straight, rubberized handle - Change saw blade by bending the handle